Stamp Community Family of Web Sites
Thousands of stamps, consistently graded, competitively priced and hundreds of in-depth blog posts to read








Stamp Community Forum
 
Username:
Password:
Save Password
Forgot your Password?

This page may contain links that result in small commissions to keep this free site up and running.

Welcome Guest! Registering and/or logging in will remove the anchor (bottom) ads. It's Free!

26A Plate No.11? Shows Partial Imprint.

 
To participate in the forum you must log in or register.
Author Previous TopicReplies: 5 / Views: 1,331Next Topic  
Pillar Of The Community
United States
2942 Posts
Posted 10/22/2016   10:24 pm  Show Profile Bookmark this topic Add stampcrow to your friends list Get a Link to this Message
"partial" is being kind. But it does show some imprint. That allows me to measure the distance from the frame line. It is 2mm.
Other than that, I don't see any plating clues.


Send note to Staff
Edited by stampcrow - 10/22/2016 10:25 pm

Rest in Peace
United States
920 Posts
Posted 10/23/2016   06:36 am  Show Profile Bookmark this reply Add Caper123 to your friends list  Get a Link to this Reply
Stampcrow, your measurement to the label leads me to believe it is from Plate 11. The label is running up and right so it is along the right pane.
I believe I can make out the '&' symbol of Toppan Carpenter & Co. Since the label started near the top of the 7th row the '&' fell on the 6th row opposite the 60th stamp approx. to the tight of the 7th perf. That's the best I can do.
Send note to Staff  Go to Top of Page
Pillar Of The Community
United States
2942 Posts
Posted 10/23/2016   1:05 pm  Show Profile Bookmark this reply Add stampcrow to your friends list  Get a Link to this Reply

Quote:
Stampcrow, your measurement to the label leads me to believe it is from Plate 11.

My thoughts also.

I had originally just set this stamp aside. Without being able to see the bottom of the frame lines, I thought there was no reason to mark it as a type IV.
I ignored the bit of imprint...

Reading through some USPCS Chronicle articles, I learned about the 2mm spacing. That reminded me of this stamp.
Just not sure if the 2mm space between the frame line and imprint is definitive in identifying this as plate 11.
Send note to Staff  Go to Top of Page
Edited by stampcrow - 10/23/2016 1:06 pm
Pillar Of The Community
United States
2555 Posts
Posted 10/23/2016   3:21 pm  Show Profile Check sinclair2010's eBay Listings Bookmark this reply Add sinclair2010 to your friends list  Get a Link to this Reply
Your plating is probably correct but I think the stamp is bowed a little in your photo. That always makes it hard. A 2.0mm spacing in and of itself is not proof that it is from Plate 11. Due to the spacing, it would probably be 11i in this case.

See the Hegland article in Chronicle 82 for plating imprint copies.
Send note to Staff  Go to Top of Page
Rest in Peace
United States
920 Posts
Posted 10/23/2016   3:26 pm  Show Profile Bookmark this reply Add Caper123 to your friends list  Get a Link to this Reply
stampcrow - Quote: Just not sure if the 2mm space between the frame line and imprint is definitive in identifying this as plate 11.


I think the only other option is plate 10 if that is a Scott 26A.

Per Carroll Chase: "On Plate 11(all states) the imprint is about 1 3/4 mm. from the stamps on the left pane, and about 2 1/2 mm. from the stamps of the right pane."

In the next paragraph he states, "On Plate 11 (all states) the imprint is about 1 1/3 mm. from the stamps on the left pane and about 2mm from the stamps on the right pane."
Send note to Staff  Go to Top of Page
Rest in Peace
United States
920 Posts
Posted 10/30/2016   06:43 am  Show Profile Bookmark this reply Add Caper123 to your friends list  Get a Link to this Reply
Sorry Stampcrow, just realized in my last reply which included the two quotes from Chase's book both said 'Plate 11'. The 1st should have said plate '10', the 2nd was correctly Plate 11.
Send note to Staff  Go to Top of Page
  Previous TopicReplies: 5 / Views: 1,331Next Topic  
 
To participate in the forum you must log in or register.

Go to Top of Page

Disclaimer: While a tremendous amount of effort goes into ensuring the accuracy of the information contained in this site, Stamp Community assumes no liability for errors. Copyright 2005 - 2026 Stamp Community Family - All rights reserved worldwide. Use of any images or content on this website without prior written permission of Stamp Community or the original lender is strictly prohibited.
Privacy Policy / Terms of Use    Advertise Here
Stamp Community Forum © 2007 - 2026 Stamp Community Forums
It took 0.65 seconds to lick this stamp. Powered By: Snitz Forums 2000 Version 3.4.05